 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HS-2608 Eden Embedded Engine Board CompactFlashMini PCI133MHz FSB SO-DIMMCRT/LVDS PanelDual LAN AudioATA/33/66/100RS-232/422/485 4 COMUSBPC/104DOC WDTSingle +5VH/W Monitor Industrial Embedded Single Board computer Copyright Disclaimers The accuracy of contents in this manual has passed thorough checking and review before publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is not liable for any infringements of patents or other rights resulting from its use. The manufacturer will not be responsible for any direct, indirect, special, incidental or consequential damages arising from the use of this product or documentation, even if advised of the possibility of such damage(s). This manual is copyrighted and BOSER Technology Co., Ltd. reserves all documentation rights. Unauthorized reproduction, transmission, translation, and storage of any form and means (i.e., electronic, mechanical, photocopying, recording) of this document, in whole or partly, is prohibited, unless granted permission by BOSER Technology Co., Ltd. BOSER Technology Co., Ltd. reserves the right to change or improve the contents of this document without due notice. BOSER Technology Co., Ltd. assumes no responsibility for any errors or omissions that may appear in this manual, nor does it make any commitment to update the information contained herein. Trademarks Trademarks BOSER is a registered trademark of BOSER Technology Co., Ltd. ISB is a registered trademark of BOSER Technology Co., Ltd. VIA is a registered trademark of VIA Technologies, Inc. Award is a registered trademark of Award Software, Inc. AMI is a registered trademark of AMI Software, Inc. All other trademarks, products and or product names mentioned herein are mentioned for identification purposes only, and may be trademarks and/or registered trademarks of their respective companies or owners. (c) Copyright 2005 BOSER Technology Co., Ltd. All Rights Reserved. Edition 1.0, August 19, 2005 Table of Contents Chapter 1 General Description ..................................1 1.1 Major Features ....................................................................... 2 1.2 Specifications ........................................................................ 3 1.3 Board Dimensions................................................................. 4 Chapter 2 Chapter 3 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 3.19 3.20 3.21 3.22 3.23 Unpacking ..................................................5 Hardware Installation ..............................7 2.1 Opening the Delivery Package............................................. 5 2.2 Inspection............................................................................... 5 Before Installation ................................................................. 7 Board Layout ......................................................................... 8 Jumper List ............................................................................ 9 Connector List ....................................................................... 9 Configuring the CPU ........................................................... 10 System Memory ................................................................... 10 DiskOnChipTM Address Setting .......................................... 10 VGA Controller .................................................................... 12 PCI E-IDE Drive Connector................................................. 14 Floppy Disk Drive Connector ............................................. 15 Serial Port Connectors ....................................................... 16 Parallel Connector............................................................... 18 Ethernet Connector............................................................. 19 USB Connector.................................................................... 19 CMOS Data Clear................................................................. 19 Power and Fan Connectors................................................ 20 Keyboard/Mouse Connectors ............................................ 20 System Front Panel Connectors........................................ 21 Watchdog Timer .................................................................. 22 Mini PCI Connector ............................................................. 24 PC/104 Connectors ............................................................. 26 Audio Connectors ............................................................... 28 CompactFlashTM Connector................................................ 28 Chapter 4 Award BIOS Setup ................................. 31 4.1 Starting Setup...................................................................... 31 4.2 Using Setup ......................................................................... 32 4.2.1 Getting Help.....................................................................................................32 4.3 Main Menu............................................................................ 33 4.4 Standard CMOS Features................................................... 34 4.5 Advanced BIOS Features ................................................... 35 4.6 Advanced Chipset Features............................................... 36 4.7 Integrated Peripherals ........................................................ 37 4.8 Power Management Setup ................................................. 38 4.9 PnP/PCI Configurations...................................................... 39 4.10 PC Health Status ................................................................. 40 4.11 Frequency/Voltage Control ................................................ 40 4.12 Load Fail-Safe Defaults ...................................................... 41 4.13 Load Optimized Defaults .................................................... 42 4.14 Set Supervisor/User Password.......................................... 42 4.15 Save & Exit Setup................................................................ 44 4.16 Exit Without Saving............................................................. 45 Chapter 5 Software Utilities..................................... 47 5.1 IDE Driver Installation ......................................................... 47 5.2 VGA Driver Installation ....................................................... 52 5.2.1 VGA Driver Installation for WIN95/98/2K........................................52 5.2.2 VGA Driver Installation for WIN NT4.0 ................................................55 5.3 LAN Driver Installation........................................................ 58 5.3.1 LAN Driver Installation for WIN95/98/2K.........................................58 5.3.2 LAN Driver Installation for WIN NT4.0 .................................................64 5.4 Audio Driver Installation..................................................... 74 Safety Instructions Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions: Do not remove boards or integrated circuits from their anti-static packaging until you are ready to install them. Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This helps to discharge any static electricity on your body. Wear a wrist-grounding strap, available from most electronic component stores, when handling boards and components. Fasten the ALLIGATOR clip of the strap to the end of the shielded wire lead from a grounded object. Please wear and connect the strap before handle the HS-2608 to ensure harmlessly discharge any static electricity through the strap. Please use an anti-static pad when putting down any components or parts or tools outside the computer. You may also use an anti-static bag instead of the pad. Please inquire from your local supplier for additional assistance in finding the necessary anti-static gadgets. NOTE: DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC PROTECTIONS. Chapter 1 General Description The HS-2608 is a 100/133MHz FSB VIA VT8606 chipset-based board designed for Mini PCI Local Bus VIA Eden 667MHz embedded low power CPU. These features combine and make the HS-2608 an ideal all-in-one industrial single board computer. Additional features include an enhanced I/O with CRT/LVDS Panel, dual LAN, Audio, and 4 COM ports interfaces. Its onboard ATA/33/66/100 to IDE drive interface architecture allows the HS-2608 to support data transfers of 33, 66 or 100MB/sec. to one IDE drive connection. Designed with the VIA VT8606 core logic chipset, the board supports VIA Eden 667MHz embedded low power CPU. The VIA VT8606 with 32MB shared main memory supporting CRT/Panel displays up to 1280 x 1024 at 24bpp colors (CRT)/1024 x 768 at 18bpp colors (Panel). It also supports 18-bit dual channel LVDS interface. System memory is also sufficient with the one SO-DIMM socket that can support up to 512MB. Additional onboard connectors include an advanced USB port providing faster data transmission, a DOS-compatible DiskOnChipTM socket with a maximum capacity of 288MB. And two external RJ-45 connectors for 10/100 Based Ethernet use. 1 To ensure the reliability in an unmanned or standalone system, the Watchdog Timer (WDT) onboard HS-2608 is designed with pure hardware that does not need the arithmetical functions of a real-time clock chip. If any program causes unexpected halts to the system, the onboard Watchdog Timer (WDT) will automatically reset the CPU or generate an interrupt to resolve such condition. 1.1 Major Features The HS-2608 comes with the following features: VIA Eden 667MHz embedded low power CPU Supports 100/133MHz FSB One SO-DIMM socket with a max. capacity of 512MB VIA VT8606/VT82C686B system chipset VIA VT82C686B, SMC 37C669 super I/O chipset VIA VT8606 display controller Dual RealTek RTL8100BL LAN controller AC97 3D audio controller Fast PCI ATA/33/66/100 IDE controller CompactFlash card adapter, four COM, two USB, PC/104 connector DOC socket supporting memory sizes of up to 288MB Single +5V power in Hardware Monitor function LVDS Panel display interface (optional) 2 1.2 Specifications CPU: VIA Eden 667MHz embedded low power CPU Memory: One SO-DIMM socket supporting up to 512MB Chipset: VIA VT8606/VT82C686B I/O Chipset: VIA VT82C686B, SMC 37C669 CompactFlash: One, Type II IDE interface adapter PCI Slot: One, Type I mini PCI slot (optional) VGA: VIA VT8606 with 32MB shared main memory supporting CRT/Panel displays up to 1280 x 1024 at 24bpp colors (CRT)/1024 x 768 at 18bpp colors (Panel) LVDS Panel: Supports 18-bit dual channel LVDS interface (optional) LAN: Dual RealTek RTL8100BL 10/100 Based LAN Audio: AC97 3D audio controller IDE: Two IDE disk drives supporting ATA/33/66/100 and with transfer rates of up to 33/66/100MB/sec. FDD: Supports up to two floppy disk drives Parallel: One enhanced bi-directional parallel port supporting SPP/ECP/EPP Serial Port: 16C550 UART-compatible RS-232/422/485 x 1 and RS-232 x 3 serial ports with 16-byte FIFO USB: Two internal USB ports PC/104: PC/104 Bus connector for 16-bit ISA Bus Keyboard/Mouse: PS/2 6-pin Mini DIN or 6-pin header DiskOnChipTM: DiskOnChipTM socket supporting memory sizes of up to 288MB BIOS: Award PnP Flash BIOS Watchdog Timer: Sets 1/2/10/20/110/220 seconds activity trigger with Reset or NMI CMOS: Battery backup Power In: Single +5V power in Temperature: 0~+60C (operating) Hardware Monitor: VIA VT82C686B Board Size: 14.5(L) x 10.2(W) cm 3 1.3 Board Dimensions 4 Chapter 2 Unpacking 2.1 Opening the Delivery Package The HS-2608 is packed in an anti-static bag. The board has components that are easily damaged by static electricity. Do not remove the anti-static wrapping until proper precautions have been taken. Safety Instructions in front of this manual describe anti-static precautions and procedures. 2.2 Inspection After unpacking the board, place it on a raised surface and carefully inspect the board for any damage that might have occurred during shipment. Ground the board and exercise extreme care to prevent damage to the board from static electricity. Integrated circuits will sometimes come out of their sockets during shipment. Examine all integrated circuits, particularly the BIOS, processor, memory modules, ROM-Disk, and keyboard controller chip to ensure that they are firmly seated. The HS-2608 delivery package contains the following items: HS-2608 Board x 1 Utility CD Disk x 1 Cables Package x 1 Cooling Fan & Heat Sink x 1 Jumper Bag x 1 User's Manual 5 NO. 1 2 3 4 5 6 7 8 Cables Package Description Keyboard/Mouse transfer cable x 1 One COM flat cable x 4 Parallel port flat cable x 1 ATA/100 IDE flat cable x 1 MIC/Audio flat cable x 1 Two USB flat cable with bracket x 1 Floppy flat cable x 1 4-pin Power In cable x 1 It is recommended that you keep all the parts of the delivery package intact and store them in a safe/dry place for any unforeseen event requiring the return shipment of the product. In case you discover any missing and/or damaged items from the list of items, please contact your dealer immediately. 6 Chapter 3 Hardware Installation This chapter provides the information on how to install the hardware using the HS-2608. This chapter also contains information related to jumper settings of switch, watchdog timer, and the DiskOnChipTM address selection etc. 3.1 Before Installation After confirming your package contents, you are now ready to install your hardware. The following are important reminders and steps to take before you begin with your installation process. 1. Make sure that all jumper settings match their default settings and CMOS setup correctly. Refer to the sections on this chapter for the default settings of each jumper. Go through the connections of all external devices and make sure that they are installed properly and configured correctly within the CMOS setup. Refer to the sections on this chapter for the detailed information on the connectors. Keep the manual and diskette in good condition for future reference and use. 2. 3. 7 3.2 Board Layout 8 3.3 Jumper List Default Setting Setting Page 22 19 10 22 16 16 12 WDT Active Type Setting: Disabled All Open Clear CMOS: Normal Operation Short 1-2 DOC Address Select: D000 Short 1-2, 3-4 WDT Timer Select: 1sec. Short 5-6, 7-8, 9-10 RS-422/485 Receiver Open Enabled/Disabled Select: Disabled COM2 Use RS-232 or RS-422/485 Open Select: RS-232 Panel Voltage Select: +3.3V Short 1-2 Jumper JP1 JP2 JP4(1-4) JP4(5-10) JP5(7-8) JP6 JP7 3.4 Connector List Definition USB Connector 5-pin ATX Power In Connector PC/104 40-pin/64-pin Connector 2-pin Power In Connector Floppy Connector Line In/Audio Out Connector RS-422/485 Connector (2x3 header) Parallel Connector RJ-45 Connector COM 3 Connector (5x2 header) PS/2 6-pin Mini DIN KB/MS Connector COM 1 Connector (5x2 header) 6-pin KB/MS Connector COM 2 Connector (5x2 header) COM 4 Connector (5x2 header) 15-pin CRT Connector 50-pin Panel Connector IDE Connector CompactFlash Connector External Reset Button LVDS Panel Connector SO-DIMM Socket Fan Connector Connector CN1 CN2 CN3/CN4 CN5 CN8 CN9 CN10 CN12 CN13/CN28 CN14 CN15 CN16 CN17 CN18 CN19 CN20 CN21 CN23 CN24 CN25 CN26/CN27 DM1 FN1 Page 19 20 26 20 15 28 16 18 19 16 20 16 20 16 16 12 12 14 28 21 12 10 20 . . . More on next page . . . 9 Connector JP3 PC1 U1 Definition System Front Panel Connector Mini PCI Connector TM DiskOnChip Socket Page 21 24 10 3.5 Configuring the CPU The HS-2608 embedded with a VIA Eden 667MHz embedded low power CPU. User don't need to adjust the frequently and check speed of VIA Eden CPU. 3.6 System Memory The HS-2608 provides one SO-DIMM socket at locations DM1. The maximum capacity of the onboard memory is 512MB. 3.7 DiskOnChipTM Address Setting The DiskOnChipTM function allows the system to boot or operate without a FDD or a HDD. DiskOnChipTM modules may be formatted as drive C or A. With DiskOnChipTM, user may also execute DOS commands such as FORMAT, SYS, COPY, XCOPY, DISCOPY and DISKCOMP etc. The U1 location on the HS-2608 is the DiskOnChipTM module socket. Jumper JP4(1-4) assigns the starting memory address of the installed module. If you have another memory device that has a similar memory capacity with that of the DOC in your system, please set both at different memory address mapping to avoid the mapping area conflicts. Failing to do so will not make the HS-2608 and the additional memory device function properly. JP4(1-4): DiskOnChipTM Address Select Address D000 (default) D800 E000 PINS 1-2 PINS 3-4 Short Open Short Short Short Open 10 3.7.1 Installing DiskOnChipTM Modules When installing a DiskOnChipTM module onto your board, please take note of the following: 1. Orient yourself properly with the location of the DiskOnChipTM socket. Try to locate the pin 1 location on your socket. Pin numbers are usually printed on either the component side or the solder side of your board. 2. Locate the Pin 1 location on your DiskOnChipTM module. More often than not, Pin 1 can be found on the lower left corner of the chip. Please refer to the diagram for the exact location. 3. Once you have figured out where the pin 1 locations are on both chip and socket, align the module's pins on an upright angle against the socket. Using both thumbs, gently press the module into the socket until all the pins are secured to their designations. Disk OnC hip Pin 1 Location 4. The installation is now complete and your module is now ready for use. NOTE: If you encounter difficulty installing your DiskOnChipTM module, please consult a qualified technician or engineer to perform the installation. 3.7.2 Removing DiskOnChipTM Modules When removing a DiskOnChipTM module from its socket, please take note of the following: 1. Loosen the contact of the module from its socket using a screwdriver. 11 2. Insert the screwdriver's flat head into a gap on either end of the socket. Do not insert the screwdriver head on either side where the pins are located. Doing so might damage the pins in the process. 3. Slowly lift the screwdriver handle upwards. This will disengage the module from its socket. NOTE: If you encounter difficulty removing your DiskOnChipTM module, please consult a qualified technician or engineer to remove it for you. 3.8 VGA Controller The HS-2608 provides three connection methods of a VGA device. CN20 offers a single standard CRT connector while CN21 is the 50-pin panel connector and CN26/CN27 are the LVDS interface connectors onboard reserved for flat panel installation. CN20: CRT Connector PIN Description PIN Description 1 3 5 7 9 11 13 15 Red Blue GND GND N/C N/C HSYNC SCL 2 4 6 8 10 12 14 Green N/C GND GND GND SDA VSYNC 6 1 11 5 10 15 CN26/CN27: LVDS Interface Connector PIN Description PIN Description 1 3 5 7 9 11 VLCD Y0M/Z0M Y1M/Z1M Y2M/Z2M YCM/ZCM GND 2 4 6 8 10 12 VLCD Y0P/Z0P Y1P/Z1P Y2P/Z2P YCP/ZCP GND VLCD Y0 Y2 Y4 Y6 GND 11 12 1 2 VLCD Y1 Y3 Y5 Y7 GND NOTE: LVDS cable should be produced very carefully. Y0 & Y1 have to be fabricated in twister pair (Y2 & Y3, Y4 & Y5, Y6 & Y7 and so on) otherwise the signal won't be stable. Please set the proper voltage of your panel using JP7 before proceeding on installing it. 12 CN21: 50-pin Panel Connector PIN. Description PIN Description 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 N/C GND VLCD ENAVEE PD0 PD2 PD4 PD6 PD8 PD10 PD12 PD14 PD16 PD18 PD20 PD22 PD24 SHFCLK DE GND P26 P28 P30 P32 P34 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 N/C GND ENAVDD GND PD1 PD3 PD5 PD7 PD9 PD11 PD13 PD15 PD17 PD19 PD21 PD23 PD25 FLM LP ENABKL P27 P29 P31 P33 P35 N/C GND 3.3V/5V ENAVEE PD0 PD2 PD4 PD6 PD8 PD10 PD12 PD14 PD16 PD18 PD20 PD22 PD24 SHFCLK DE GND P26 P28 P30 P32 P34 49 50 1 2 N/C GND ENAVDD GND PD1 PD3 PD5 PD7 PD9 PD11 PD13 PD15 PD17 PD19 PD21 PD23 PD25 FLM LP ENABKL P27 P29 P31 P33 P35 NOTE: Please set the proper voltage of your panel using JP7 before proceeding on installing it. The HS-2608 has an onboard jumper that selects the working voltage of the flat panel connected to the system. Jumper JP7 offers two voltage settings for the user. JP7: Panel Voltage Select Options +3.3V (default) +5V Settings Short 1-2 Short 2-3 +3.3V VLCD +5V 1 3 13 3.9 PCI E-IDE Drive Connector CN23 is a standard 44-pin 2.0mm pitch connector daisy-chain driver connector serves the PCI E-IDE drive provisions onboard the HS-2608. A maximum of two ATA/33/66/100 IDE drives can be connected to the HS-2608 via CN23. CN23: IDE Connector PIN 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 Description IDERST PDD7 PDD6 PDD5 PDD4 PDD3 PDD2 PDD1 PDD0 GND PDDREQ IOW# IOR# PIORDY PDDACK# IRQ14 PDA1 PDA0 PDCS1# HDD Active VCC GND PIN 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 GND 470 with GND Description GND PDD8 PDD9 PDD10 PDD11 PDD12 PDD13 PDD14 PDD15 N/C GND GND GND 470 with GND GND N/C PD33/66 PDA2 PDCS3# GND VCC N/C PD33/66 PDCS3# PDD10 PDD11 PDD12 PDD13 PDD14 PDD15 PDD8 PDD9 PDA2 GND GND ' GND GND GND VCC VCC N/C N/C 2 1 IDERST IOW# PDDREQ IOR# PDA1 PDD7 PDD6 PDD5 PDD4 PDD3 PDD2 PDD1 PDD0 PDDACK# IRQ14 PDA0 PDCS1# PIORDY GND HDD ACTIVE GND N/C 44 43 14 3.10 Floppy Disk Drive Connector The HS-2608 uses a standard 34-pin header connector, CN8, for floppy disk drive connection. A total of two FDD drives may be connected to CN8 at any given time. CN8: Floppy Connector PIN 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 Description GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND PIN 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 Description DRVDEN0 N/C DRVDEN1 INDEX# MTR0# DS1# DS0# MTR1# DIR# STEP# WDATA# WGATE# TRAK00# WRTPRT# RDATA# HDSEL# DSKCHG# DSKCHG# 34 33 GND WRTPRT# DRVDEN0 DRVDEN1 TRAK00# WGATE# WDATA# ' RDATA# GND 2 u 1 GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND HDSEL# INDEX# MTR0# MTR1# STEP# DS1# DS0# DIR# N/C 15 3.11 Serial Port Connectors The HS-2608 offers two NS16C550 compatible UARTs with Read/Receive 16-byte FIFO serial ports and four internal 10-pin headers and one RS-422/485 connector. CN16: COM1 Connector (5x2 Header) PIN Description PIN Description 1 3 5 7 9 DCD1 RXD1 TXD1 DTR1 GND 2 4 6 8 10 DSR1 RTS1 CTS1 RI1 N/C DCD1 1 RXD1 3 TXD1 DTR1 GND 5 7 9 2 DSR1 4 RTS1 6 CTS1 8 RI1 10 N/C CN18: COM2 Connector (5x2 Header) PIN Description PIN Description 1 3 5 7 9 DCD2 RXD2 TXD2 DTR2 GND 2 4 6 8 10 DSR2 RTS2 CTS2 RI2 N/C DCD2 1 RXD2 3 TXD2 DTR2 GND 5 7 9 2 DSR2 4 RTS2 6 CTS2 8 RI2 10 N/C CN14: COM3 Connector (5x2 Header) PIN Description PIN Description 1 3 5 7 9 DCD3 RXD3 TXD3 DTR3 GND 2 4 6 8 10 DSR3 RTS3 CTS3 RI3 N/C DCD3 1 RXD3 3 TXD3 DTR3 GND 5 7 9 2 DSR3 4 RTS3 6 CTS3 8 RI3 10 N/C 16 CN19: COM4 Connector (5x2 Header) PIN Description PIN Description 1 3 5 7 9 DCD4 RXD4 TXD4 DTR4 GND 2 4 6 8 10 DSR4 RTS4 CTS4 RI4 N/C DCD4 1 RXD4 3 TXD4 DTR4 GND 5 7 9 2 DSR4 4 RTS4 6 CTS4 8 RI4 10 N/C CN10: RS-422/485 Connector (5x2 Header, COM2) PIN Description PIN Description 1 3 5 TXRX+ GND 2 4 6 TX+ RXRTSTX- 1 RX+ 3 GND 5 2 TX+ 4 RX6 VCC NOTE: The terminal resistance of RX & TX is set at 180. Options Always Enable Always Disabled (default) JP5(7-8): RS-422/485 Receiver Enabled/Disabled Select Settings Short Open 2 1 8 7 JP6: COM2 use RS-232 or RS-422/485 Select Options RS-232 (default) RS-422/485 Settings Open Short 1 2 NOTE: RS-422/485 port uses COM2. RS-232 of COM2 cannot be used while RS-422/485 is selected. 17 3.12 Parallel Connector CN12 is a standard 26-pin flat cable connector deigned to accommodate parallel port connection on the HS-2608. CN12: Parallel Connector PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 Auto Form Feed Description Strobe DATA 0 DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 DATA 6 DATA 7 Acknowledge Busy Paper Empty Printer Select Printer Select LN# PIN 14 15 16 17 18 19 20 21 22 23 24 25 26 Description Auto Form Feed ERROR# Initialize Printer Select LN# GND GND GND GND GND GND GND GND GND ERROR# Initialize GND GND GND GND GND GND GND GND Paper Empty GND 26 13 Printer Select 14 1 DATA0 DATA1 DATA2 DATA3 DATA4 DATA5 DATA6 DATA7 Strobe Acknowledge Busy 18 3.13 Ethernet Connector The HS-2608 provides two external RJ-45 interface connectors. Please refer to the following for its pin information. CN13/CN28: RJ-45 Connector PIN Description 1 2 3 4 5 6 7 8 TX+ TXRX+ R/C GND R/C GND RXR/C GND R/C GND 1 2 TXRX+ R/C GND R/C GND RXR/C GND R/C GND TX+ 8 4 3.14 USB Connector The HS-2608 provides one 8-pin connectors, at location CN1, for two USB connections to the HS-2608. CN1: USB Connector USBD0+ USBD0- 1 3 5 7 VCC USBD1USBD1+ GND 2 4 6 8 VCC USBD0USBD0+ GND 2 1 USBD1USBD1+ GND VCC GND 8 7 3.15 CMOS Data Clear The HS-2608 has a Clear CMOS jumper on JP2. JP2: Clear CMOS Options Normal Operation (default) Clear CMOS Settings Short 1-2 Short 2-3 1 VCC3 VBAT GND VCC PIN Description PIN Description 3 19 IMPORTANT: Before you turn on the power of your system, please set JP2 to Short 1-2 for normal operation. 3.16 Power and Fan Connectors HS-2608 provides one 5-pin power connectors at CN2. And one 2-pin power in at CN5. CN2: 5-pin ATX Power In Connector PS_ON GND 5VSB +12V 1 3 5 GND +12V VCC 2 4 PS_ON 5VSB 1 VCC 5 PIN Description PIN Description CN5: 2-pin Power In Connector PIN Description 1 2 VCC GND 2 1 VCC GND FN1: Fan Connector PIN 1 2 3 Description CPU Fan1 +5V GND 3 GND +5V Fan Speed 1 Connector FN1 onboard HS-2608 is a 3-pin fan power output connector. And HS-2608 supports +5V Fan only. 3.17 Keyboard/Mouse Connectors The HS-2608 offers two possibilities for keyboard/mouse connections. The connections are via CN15 for an external PS/2 type keyboard/mouse or via CN17 for an internal 6-pin cable converter to an keyboard/mouse. 20 CN15: PS/2 6-pin Mini DIN Keyboard/Mouse Connector PIN 1 2 3 4 5 6 Description Keyboard Data Mouse Data GND +5V Keyboard Clock Mouse Clock Keyboard Clock 3 GND 5 1 Data 6 Keyboard 2 Mouse Data 4 +5V Mouse Clock CN17: 6-pin Keyboard/Mouse Connector PIN 1 2 3 4 5 6 Description Keyboard Clock Keyboard Data Mouse Data GND +5V Mouse Clock 1 2 3 4 5 6 Keyboard Clock Keyboard Data 3.18 System Front Panel Connectors The HS-2608 has one LED at location JP3 that indicates the power-on status. This visual feature of the IDE LED may also be connected to an external IDE LED, Speaker, Reset Switch, Power LED, EXT SMI, Power Button, and SLP Button via connector JP3(13-15), JP3(1-3-5-7), JP3(9-11), JP3(2-4), JP3(6-8), JP3(10-12), JP3(14-16). JP3: System Front Panel Connector PIN Description 1 3 5 7 9 11 13 15 330 Pull +5V GND +5V Speaker GND Reset Switch 330 Pull +5V HDD LED PIN 2 4 6 8 10 12 14 16 Description 330 Pull +5V GND EXT SMI GND PW Button GND SLP Button GND Mouse Clock Mouse Data GND +5V 21 Connector JP3 Orientation 1 3 SPEAKER 5 7 9 RST_SW HD_LED 11 2 4 6 8 10 12 SLP button PWR button PWR LED EXT_SMI 13 14 15 16 CN25: External Reset Button PIN Description Reset GND 1 1 2 Reset GND 1 2 3.19 Watchdog Timer There are three access cycles of Watch-Dog Timer as Enable, Refresh and Disable. The Enable cycle proceeds via READ PORT 443H whereas the Disable cycle proceeds via READ PORT 045H. A continued Enable cycle after a first Enable cycle means Refresh. Once the Enable cycle is active, a Refresh cycle is requested before the time-out period. This restarts counting of the WDT period. When the time counting goes over the preset period of WDT, it will assume that the program operation is abnormal. A System Reset signal to re-start or a NMI cycle to the CPU transpires when such error happens. Jumper JP1 is used to select the function of Watchdog Timer. JP1: Watchdog Timer Active Type Setting Options Active NMI System Reset Disabled WDT (default) Settings Short 1-2 Short 2-3 Open 3 22 JP4(5-10): WDT Timeout Period Select Period 1 sec (default) 2 sec 10 sec 20 sec 110 sec 220 sec PINS 5-6 Short Open Short Open Short Open PINS 7-8 PINS 9-10 Short Short Open Open Short Short Short Short Short Short Open Open The Watchdog Timer is disabled after the system Power-On. It can be enabled via an Enable cycle and reading the control port (443H), or via a Refresh cycle and reading the control port (443H), or via a Disable cycle and reading the disable control port (045H). After an Enable cycle of WDT, user must immediately execute a Refresh cycle to WDT before its period setting comes to an end every 1, 2, 10, 20, 110 or 220 seconds. If the Refresh cycle does not activate before WDT period cycle, the onboard WDT architecture will issue a Reset or NMI cycle to the system. There are three I/O ports that control the Watchdog Timer. 443H 443H 045H I/O Read I/O Read I/O Read The Enable cycle The Refresh cycle The Disable cycle The following sample program shows how to Enable, Disable and Refresh the Watchdog Timer: WDT_EN_RF WDT_DIS WT_Enable EQU EQU PUSH PUSH MOV IN POP POP RET PUSH PUSH MOV IN POP POP RET 0443H 0045H AX DX DX,WDT_EN_RF AL,DX DX AX ; keep AX DX ; enable the WDT ; get back AX, DX WT_Refresh AX DX DX,WDT_ET_RF AL,DX DX AX ; keep AX, DX ; refresh the WDT ; get back AX, DX 23 WT_DISABLE PUSH PUSH MOV IN POP POP RET AX DX DX,WDT_DIS AL,DX DX AX ; disable the WDT ; get back AX, DX 3.20 Mini PCI Connector HS-2608 supports a Mini PCI connector. The peripheral component with standard Type1 Mini PCI can be used. For particular requirement, please refer to "BOSER Mini PCI series product" on website or contact with us. PC1: Mini PCI Connector PIN 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 Description INTB# 3.3V INTA# GND CLK GND REQ# 3.3V AD[31] AD[29] GND AD[27] AD[25] REQ1 C/BE[3]# AD[23] GND AD[21] AD[19] GND AD[17] C/BE[2]# IRDY# 3.3V N/C PIN 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 Description 5V INTD# INTC# N/C RST# 3.3V GNT# GND PME# GNT1 AD[30] 3.3V AD[28] AD[26] AD[24] AD[21] GND AD[22] AD[20] PAR AD[18] AD[16] GND FRAME# TRDY# . . . More on next page . . . 24 PIN 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 Description SERR# GND PERR# C/BE[1]# AD[14] GND AD[12] AD[10] GND AD[8] AD[7] 3.3V AD[5] REQ2 AD[3] 5V AD[1] GND N/C N/C N/C N/C N/C N/C N/C PIN 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 100 Description STOP# 3.3V DEVSEL# GND AD[15] AD[13] AD[11] GND AD[9] C/BE[0]# 3.3V AD[6] AD[4] AD[2] AD[0] GNT2 GNT3 GND IRQ7 N/C N/C N/C REQ3 N/C N/C 2 100 1 Mini PCI Socket pin orientation 99 25 3.21 PC/104 Connectors The PC/104 expansion bus offers provisions to connect all types of PC/104 modules. With the PC/104 bus being known as the new generation of industrial embedded 16-bit PC standard bus, thousands of PC/104 modules from multiple venders can be easily installed onboard. The detailed pin assignment of the PC/104 expansion bus connectors CN3 and CN4 are listed on the following tables: NOTE The PC/104 connector allows direct plugging or stack-through piling of PC/104 modules without requiring the PC/104 mounting kit. CN3: PC/104 40-pin Connector PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Description PIN Description GND -MEMCS16 -IOSC16 IRQ10 IRQ11 IRQ12 IRQ15 IRQ14 -DACK0 DRQ0 -DACK5 DRQ5 -DACK6 DRQ6 -DACK7 DRQ7 +5V -MASTER GND GND 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 GND -SBHE SA23 SA22 SA21 SA20 SA19 SA18 SA17 -MEMR -MEMW SD8 SD9 SD10 SD11 SD12 SD13 SD14 SD15 N/C Connector diagram rotated 90 degrees clockwise from original position 1 21 20 40 26 CN4: PC/104 64-pin Connector PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Description PIN Description -IOCHECK SD7 SD6 SD5 SD4 SD3 SD2 SD1 SD0 IOCHRDY AEN SA19 SA18 SA17 SA16 SA15 SA14 SA13 SA12 SA11 SA10 SA9 SA8 SA7 SA6 SA5 SA4 SA3 SA2 SA1 SA0 GND 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 GND RESETDRV +5V IRQ9 N/C N/C N/C N/C N/C GND -SMEMW -SMEMR -IOW -IOR -DACK3 DRQ3 -DACK1 DRQ1 -REFRESH SYSCLK IRQ7 IRQ6 IRQ5 IRQ4 IRQ3 -DACK2 TC BALE +5V OSC N/C GND Connector diagram rotated 90 degrees clockwise from original position 1 33 32 64 27 3.22 Audio Connectors The HS-2608 has an onboard AC97 3D audio interface. The following tables list the pin assignments of the Line In/Audio Out connector. CN9: Line In/Audio Out Connector PIN Description PIN Description 1 3 5 7 AOUTL GND MIC IN GND 2 4 6 8 AOUTR GND LIR LIL AOUT_L GND MIC IN GND 7 8 1 2 AOUT_R GND LIR LIL 3.23 CompactFlashTM Connector The HS-2608 also offers an optional CompactFlashTM connector which is IDE interface located at the solder side of the board (beneath the SO-DIMM connector). The designated CN24 connector, once soldered with an adapter, can hold CompactFlashTM cards of various sizes. Please turn off the power before inserting the CD card. CN24: CompactFlashTM Connector PIN 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 Description GND DATA 4 DATA 6 SDCS1# GND GND VCC (+5V) GND GND SDA1 DATA 0 DATA 2 N/C DATA 11 DATA 13 DATA 15 PIN 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 Description DATA 3 DATA 5 DATA 7 GND GND GND GND GND SDA2 SDA0 DATA 1 470 pull to GND N/C DATA 12 DATA 14 SDCS3# . . . More on next page . . . 28 PIN 33 35 37 39 41 43 45 47 49 Description N/C IOW IRQ CS Reset N/C IDE LED DATA 8 DATA 10 PIN 34 36 38 40 42 44 46 48 50 Description IOR EWE0 VCC (+5V) N/C IORDY REQ 0 PDIAG DATA 9 GND Inserting a CompactFlashTM card into the adapter is not a difficult task. The socket and card are both keyed and there is only one direction for the card to be completely inserted. Refer to the diagram on the following page for the traditional way of inserting the card. PC Si B de So Vi lde ew r C om pa ct Fl as hT Re M ar Si de CE Fa Ma br de iq in ue J A ap u an Ja / po n CF 29 This page is intentionally left blank. 30 Chapter 4 Award BIOS Setup The HS-2608 uses Award BIOS for the system configuration. The Award BIOS setup program is designed to provide the maximum flexibility in configuring the system by offering various options that could be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features. 4.1 Starting Setup The Award BIOS is immediately activated when you first power on the computer. The BIOS reads the system information contained in the CMOS and begins the process of checking out the system and configuring it. When it finishes, the BIOS will seek an operating system on one of the disks and then launch and turn control over to the operating system. While the BIOS is in control, the Setup program can be activated in one of two ways: 1. By pressing Press DEL to enter SETUP. If the message disappears before you respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the "RESET" button on the system case. You may also restart by simultaneously pressing 31 4.2 Using Setup In general, you use the arrow keys to highlight items, press Up arrow Down arrow Left arrow Right arrow Esc key Move to previous item Move to next item Move to the item in the left hand Move to the item in the right hand Main Menu -- Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu Increase the numeric value or make changes Decrease the numeric value or make changes Increase the numeric value or make changes Decrease the numeric value or make changes General help, only for Status Page Setup Menu and Option Page Setup Menu Change color from total 16 colors. F2 to select color forward, (Shift) F2 to select color backward Calendar, only for Status Page Setup Menu Reserved Restore the previous CMOS value from CMOS, only for Option Page Setup Menu Load the default CMOS value from BIOS default table, only for Option Page Setup Menu Load the default Reserved Reserved Save all the CMOS changes, only for Main Menu PgUp key PgDn key + key - key F1 key (Shift)F2 key F3 key F4 key F5 key F6 key F7 key F8 key F9 key F10 key 4.2.1 Getting Help Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press 32 4.3 Main Menu Once you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status EscQuit F9Menu in BIOS F10Save & Exit Setup Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving Select Item Time, Date, Hard Disk Type... NOTE: A brief description of the highlighted choice appears at the bottom of the screen. 33 4.4 Standard CMOS Features The Standard Setup is used for the basic hardware system configuration. The main function is for Data/Time and Floppy/Hard Disk Drive settings. Please refer to the following screen for the setup. When the IDE hard disk drive you are using is larger than 528MB, you must set the HDD mode to LBA mode. Please use the IDE Setup Utility in BIOS SETUP to install the HDD correctly. Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) IDE IDE IDE IDE Mon, Aug 9 2004 10 : 32 : 57 [Auto] [Auto] [Auto] [Auto] [1.44M, 3.5in.] [EGA/VGA] [All, But Keyboard] 640K 252928K 253952K +/-/PU/PD: Value F10: Save ESC: Quit F1: General Help F6: Fail-Safe Defaults F7: Optimized Defaults Item Help Menu Level Change the day, month, year and century Primary Master Primary Slave Secondary Master Secondary Slave Drive A Video Halt On Base Memory Extended Memory Total Memory : Select Item F5: Previous Values 34 4.5 Advanced BIOS Features This section allows you to configure your system for the basic operation. You have the opportunity to select the system's default speed, boot-up sequence, keyboard operation, shadowing and security. Phoenix - AwardBIOS CMOS Setup Utility Advanced CMOS Features Virus Warning CPU Internal Cache External Cache CPU L2 Cache ECC Checking Processor Number Feature Quick Power On Self Test First Boot Device Second Boot Device Third Boot Device Boot Other Device Swap floppy Drive Boot Up Floppy Seek Boot Up NumLock Status Gate A20 Option Typematic Rate Setting X Typematic Rate (Chars/Sec) X Typematic Delay (Msec) Security Option OS Select For DRAM > 64MB Video BIOS Shadow C8000-CBFFF Shadow CC000-CFFFF Shadow D0000-D3FFF Shadow D4000-D7FFF Shadow D8000-DBFFF Shadow DC000-DFFFF Shadow Full Screen LOGO Show Small Logo(EPA) Show : Select Item F5: Previous Values [Disabled] [Enabled] [Enabled] [Enabled] [Enabled] [Enabled] [Floppy] [HDD-0] [CDROM] [Enabled] [Disabled] [Enabled] [On] [Fast] [Disabled] 6 250 [Setup] [Non-OS2] [Enabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] [Enabled] F10: Save F6: Fail-Safe Defaults Item Help Menu Level +/-/PU/PD: Value ESC: Quit F1: General Help F7: Optimized Defaults 35 4.6 Advanced Chipset Features This section allows you to configure the system based on the specific features of the installed chipset. This chipset manages bus speeds and the access to the system memory resources, such as DRAM and the external cache. It also coordinates the communications between the conventional ISA and PCI buses. It must be stated that these items should never be altered. The default settings have been chosen because they provide the best operating conditions for your system. You might consider making any changes only if you discover that the data has been lost while using your system. Phoenix - AwardBIOS CMOS Setup Utility Advanced Chipset Features DRAM Timing By SPD DRAM Clock SDRAM Cycle Length Bank Interleave Memory Hole P2C/C2P Concurrency System BIOS Cacheable Video RAM Cacheable Frame Buffer Size AGP Aperture Size AGP-4X Mode AGP Driving Control X AGP Driving Value Select Display Device Panel Type OnChip USB USB Keyboard Support OnChip Sound CPU to PCI Write Buffer PCI Dynamic Bursting PCI Master 0 WS Write PCI Delay Transaction PCI#2 Access #1 Retry AGP Master 1 WS Write AGP Master 1 WS Read : Select Item F5: Previous Values [Disabled] [Host CLK] [3] [Disabled] [Disabled] [Enabled] [Enabled] [Enabled] [16M] [64M] [Enabled] [Auto] DA [CRT] [00] [Enabled] [Disabled] [Auto] [Enabled] [Enabled] [Enabled] [Disabled] [Enabled] [Disabled] [Disabled] F10: Save F6: Fail-Safe Defaults Item Help Menu Level +/-/PU/PD: Value ESC: Quit F1: General Help F7: Optimized Defaults 36 4.7 Integrated Peripherals The IDE hard drive controllers can support up to two separate hard drives. These drives have a master/slave relationship that is determined by the cabling configuration used to attach them to the controller. Your system supports two IDE controllers--a primary and a secondary--so you can install up to four separate hard disks. PIO means Programmed Input/Output. Rather than having the BIOS issue a series of commands to affect the transfer to or from the disk drive, PIO allows the BIOS to tell the controller what it wants and then let the controller and the CPU perform the complete task by themselves. This is much simpler and more efficient (also faster). Phoenix - AwardBIOS CMOS Setup Utility Integrated Peripherals On-Chip IDE Channel0 On-Chip IDE Channel1 IDE Prefetch Mode Primary Master Primary Slave Secondary Master PIO PIO PIO [Enabled] [Enabled] [Enabled] [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] [PCI Slot] [Enabled] [Enabled] [3F8/IRQ4] [2F8/IRQ3] [Standard] Half No, Yes [378/IRQ7] [Normal] [3] [EPP1.9] [3E8] [IRQ10] [2E8] [IRQ11] [Enabled] [Disabled] [220H] [IRQ 5] [DMA 1] [Disabled] [330-333H] +/-/PU/PD: Value F10: Save ESC: Quit F1: General Help F6: Fail-Safe Defaults F7: Optimized Defaults Item Help Menu Level Secondary Slave PIO Primary Master UDMA Primary Slave UDMA Secondary Master UDMA Secondary Slave UDMA Init Display First IDE HDD Block Mode Onboard FDD Controller Onboard Serial Port 1 Onboard Serial Port 2 UART 2 Mode X IR Function Duplex X TX, RX inverting enable Onboard Parallel Port Onboard Parallel Port Mode ECP Mode Use DMA Parallel Port EPP Type Onboard Serial Port 3 Serial Port 3 Use IRQ Onboard Serial Port 4 Serial Port 4 Use IRQ Onboard Legacy Audio Sound Blaster SB I/O Base Address SB IRQ Select SB DMA Select MPU-401 MPU-401 I/O Address : Select Item F5: Previous Values 37 4.8 Power Management Setup The Power Management Setup allows user to configure the system for saving energy in a most effective way while operating in a manner consistent with his own style of computer use. Phoenix - AwardBIOS CMOS Setup Utility Power Management Setup ACPI function Power Management ACPI Suspend Type PM Control by APM Video Off Option Video Off Method MODEM Use IRQ Soft-Off by PWRBTN Wake Up Events : Select Item F5: Previous Values [Disabled] Item Help [Press Enter] Menu Level [S1(POS)] [Yes] [Suspend -> Off] [V/H SYNC+Blank] [NA] [Instant-Off] [Press Enter] +/-/PU/PD: Value F10: Save ESC: Quit F1: General Help F6: Fail-Safe Defaults F7: Optimized Defaults Phoenix - AwardBIOS CMOS Setup Utility Power Management Power Management HDD Power Down Doze Mode Suspend Mode : Select Item [User Define] [Disabled] [Disabled] [Disabled] +/-/PU/PD: Value F10: Save Item Help Menu Level ESC: Quit F1: General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults Phoenix - AwardBIOS CMOS Setup Utility Wake Up Events VGA LPT & COM HDD & FDD PCI Master Modem Ring Resume RTC Alarm Resume X Date (of Month) X Resume Time (hh:mm:ss) Primary INTR IRQs Activity Monitoring : Select Item F5: Previous Values [OFF] [LPT/COM] [ON] [OFF] [Disabled] [Disabled] 0 0:0:0 [ON] [Press Enter] F10: Save F6: Fail-Safe Defaults Item Help Menu Level +/-/PU/PD: Value ESC: Quit F1: General Help F7: Optimized Defaults 38 4.9 PnP/PCI Configurations This section describes the configuration of the PCI bus system. PCI, or Peripheral Components Interconnect, is a system that allows I/O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings. Phoenix - AwardBIOS CMOS Setup Utility PnP/PCI Configurations PNP OS Installed Reset Configuration Data Resources Controlled By X IRQ Resources X DMA Resources PCI/VGA Palette Snoop Assign IRQ For VGA Assign IRQ For USB [No] [Disabled] [Auto(ESCD)] Press Enter Press Enter [Disabled] [Enabled] [Enabled] Item Help Menu Level Default is Disabled. Select Enabled to reset Extended System Configuration Data ESCD) when you exit Setup if you have Installed a new add-on And the system Reconfiguration has Caused such a serious Conflict that the OS Cannot boot ESC: Quit F1: General Help : Select Item +/-/PU/PD: Value F10: Save F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults 39 4.10 PC Health Status Phoenix - AwardBIOS CMOS Setup Utility PC Health Status Current Current Current Current VCORE 2.5V 3.3V 5V 12V CPU Temp. System Temp. CPUFAN1 Speed CPUFAN2 Speed Item Help Menu Level : Select Item +/-/PU/PD: Value F10: Save ESC: Quit F1: General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults 4.11 Frequency/Voltage Control Phoenix - AwardBIOS CMOS Setup Utility Frequency/Voltage Control Auto Detect DIMM/PCI Clk Spread Specturm CPU Host Clock (CPU/PCI) [Enabled] [Disabled] [Default] Item Help Menu Level : Select Item +/-/PU/PD: Value F10: Save ESC: Quit F1: General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults 40 4.12 Load Fail-Safe Defaults When you press Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Load Fail-Safe Defaults (Y/N)? N word PnP/PCI Configurations PC Health Status EscQuit F9Menu in BIOS F10Save & Exit Setup Save & Exit Setup Exit Without Saving Select Item Time, Date, Hard Disk Type... 41 4.13 Load Optimized Defaults When you press Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Manageme Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password word Load Optimized Defaults (Y/N)? N PnP/PCI Configurations PC Health Status EscQuit F9Menu in BIOS F10Save & Exit Setup Save & Exit Setup Exit Without Saving Select Item Time, Date, Hard Disk Type... 4.14 Set Supervisor/User Password Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Manageme Enter Password: Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password word Save & Exit Setup Exit Without Saving Select Item PnP/PCI Configurations PC Health Status EscQuit F9Menu in BIOS F10Save & Exit Setup Time, Date, Hard Disk Type... 42 You can set either supervisor or user password, or both of them. The differences between are: supervisor password: can enter and change the options of the setup menus. user password: just can only enter but do not have the right to change the options of the setup menus. When you select this function, the following message will appear at the center of the screen to assist you in creating a password. ENTER PASSWORD: Type the password, up to eight characters in length, and press 43 4.15 Save & Exit Setup Press Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Manageme Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password word SAVE to CMOS and EXIT (Y/N)? N PnP/PCI Configurations PC Health Status EscQuit F9Menu in BIOS F10Save & Exit Setup Save & Exit Setup Exit Without Saving Select Item Time, Date, Hard Disk Type... 44 4.16 Exit Without Saving Pressing Phoenix - AwardBIOS CMOS Setup Utility Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Manageme Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password word Quit without Saving (Y/N)? N PnP/PCI Configurations PC Health Status EscQuit F9Menu in BIOS F10Save & Exit Setup Save & Exit Setup Exit Without Saving Select Item Time, Date, Hard Disk Type... 45 This page is intentionally left blank. 46 Chapter 5 Software Utilities This chapter contains the detailed information of IDE, VGA and LAN driver installation procedures. 5.1 IDE Driver Installation The utility disk that came with the delivery package contains an auto-run program that invokes the installation programs for the IDE, VGA and Audio drivers. The following describes the installation procedures of each driver. 1. Insert Utility CD Disk to your CD ROM. The main menu will pop up as shown below. 47 2. Press "VIA 4 IN 1" and to go Setup. 3. Once the Welcome screen appears on the screen, make sure to close any applications running and then click on the Next button. 48 4. When the Readme window pops on the screen, you may read the whole document including the license agreement or just press Yes to skip through and continue installation. 5. The 4 in 1 Setup dialog is now displayed. Select on Normally Install and then click on Next. 49 6. The next window lists all components detected in your system and asks you to select the ones requiring drivers. Tick on all items then proceed by clicking on the Next button below the screen. 7. The program starts to install the ATAPI driver when you click the Next button on the screen below. 8. When the ATAPI driver is completely installed. The utility then displays your DMA mode status and allows you to enable it. Tick on the box and press on the Next button to continue. 50 9. The following screen then gives you the choice of installing the AGP driver in standard o turbo mode. Select on the Standard Mode and then click on Next to proceed. 10. Installation of the AGP driver is now complete. Once the screen below appears, select on restarting your computer to activate all drivers/settings completed. 51 5.2 1. VGA Driver Installation With the Utility CD Disk still in your CD ROM drive, open the File Manager and then select the CD-ROM drive. As soon as the system reads the disk, the VGA Menu screen below will appear on your display. Click on VIA_8606 from the main menu. 5.2.1 VGA Driver Installation for WIN95/98/2K 52 2. Select the operating system of your computer to proceed with the installation process. 53 3. Once the Welcome screen appears on the screen, make sure to close applications that are running and then click the Next button. 4. When the display below appears on your screen, Setup is already ready to install and copy the related files onto your hard drive. Click on the Next button to proceed. 54 5. After the installation finishes, you will be prompted to restart your system. We recommend you to reboot your computer to allow the new settings to take effect. Click on the Finish button to reboot. 5.2.2 VGA Driver Installation for WIN NT4.0 1. Click the Start button on the lower left hand corner of your screen, then select Setting. Choose Control Panel and double-click on the Display icon to launch its Display Properties window. Click on the Settings tab, and then choose Display Type. In the Change Display Type window, click on Have Disk. 55 2. Specify the path of the new driver and then press on Enter. (If in driver D:, type d:\Vga/Via_8606/Nt40) 3. Select S3 Graphics Twister 6. Click OK or press Enter. 56 7. You will see warning panel about Third Party Drivers. Click on Yes to finish the installation. 8. Once the installation is completed, you must shut down the system and restart for the new driver to take effect. 57 5.3 LAN Driver Installation 5.3.1 LAN Driver Installation for WIN95/98/2K 1. With the Utility CD Disk still in your CD ROM drive, right click on My Computer icon from the Windows menu. Select on System Properties and then proceed to the Device Manager from the main menu. 58 2. Select on Other Devices from the list of devices then double-click on PCI Ethernet Controller. 59 3. The PCI Ethernet Controller Properties screen then appears, allowing you to re-install the driver. Select Driver from the main menu to proceed. 4. The window then displays the current status of your LAN driver. Press on Update Driver button to continue. 5. The program will then launch the Update Device Driver Wizard window that will install your device driver. Click on the Next button to proceed to the next step. 60 6. When the succeeding window asks you what you wish Windows to do, tick on the "Search for a better driver...." Click on the Next button to proceed. 7. The Update Device Driver Wizard will then ask you to specify, by ticking, the path of the new driver. Tick on the open boxes where you require the program to search for the device driver then click on the Browse button to manually specify the path. 61 8. Press on the OK button as soon as you have located the path of your driver. 9. Once the program returns to the Add New Hardware Wizard screen, your specified location will appear. Press on the Next button to continue. 10. Once the program detects the device driver (*.inf) file from your specified location, it will automatically copy the files into your hard drive. 62 11. When copying of driver files finishes, the program will then ask you to insert your Windows. 12. The program then copies the necessary files from your Windows installation disk to complete the driver setup process. Once the driver is completely installed, the following message appears on your display. Click on the Finish button to proceed. 13. Restart your computer to make the new system settings take effect. Click on the Yes button when the screen below appears and your LAN Driver for Win95 and Win98 are now completely installed. 63 5.3.2 LAN Driver Installation for WIN NT4.0 1. With the Utility CD Disk still in your CD ROM drive, right click on Network Neighborhood icon from the Windows menu. Select on Properties. 2. The system automatically detects the absence of Windows NT Networking. Click on the Yes button to start installation. 64 3. Tick on the "Wired to Network" once the following screen appears. Click on the Next to proceed. 4. Click on the Start Search button for the program to locate the Network Adapter. 65 5. Once setup finishes the search, it will list a number of adapters for you to choose from. Press on the Have Disk button to assign the driver path location. 6. Setup now asks you for the location of the driver. When you have entered the new driver path, press on the OK button to continue. 66 7. When Setup finds the information it needs about the new driver, it will display the device it found on the following screen. Press on the OK button to accept and proceed. 8. Setup then returns to Network Setup Wizard screen and displays your new Network Adapter. Click on Next to continue. 67 9. The Network Setup Wizard then allows you to set the Network Protocols on your network. Select the appropriate protocol and then click on Next to continue. 10. Before Setup starts installing the components found and the settings you made, it will give you the option to proceed or go back for changes from the following screen. Click on the Next button once you are sure of your devices. 68 11. Windows NT Setup will then need to copy files necessary to update the system information. Specify the path then press Continue. 12. Once it finishes copying the files, Setup will now allow you to choose the Duplex Mode of your LAN controller. Press on the Continue button after making your selection. 69 13. When Setup asks if you wish to change the TCP/IP settings of your system, select the appropriately. The default choice is No. 14. Setup then starts the Networking installation and copies the files. 70 15. When Setup finishes copying, the TCP/IP properties of your system will then pop up on your screen like the one shown below. Make the necessary changes then click on OK to continue. 16. When the screen below appears, click on Next to continue. 71 17. Setup then prompts you that it is ready to start the network. You may complete the installation thereafter. Click on Next to continue. 18. Assign the workgroup or domain setting of your computer. Click on Next to continue. 72 19. Restart your computer once the screen below appears. Click on Finish to continue. 20. Click on the Yes button to restart your computer. The LAN driver installation for WIN NT4.0 is now complete. 73 5.4 1. Audio Driver Installation With the Utility CD Disk still in your CD ROM drive, open the File Manager and then select the CD-ROM drive. As soon as the system reads the disk, the VGA Menu screen below will appear on your display. Click on VIA_AC97 from the main menu. 2. Once the Welcome screen appears on the screen, make sure to close applications that are running and then click the Next button. 74 3. The Select Components dialog box is now displayed. Select on Install driver and then click on Next. 4. The program will now require the Windows installation disk for proper hardware installation. Insert the CD and then click on Next. 75 5. When the display below appears on your screen, Setup is already installing and copying the related files onto your hard drive. Click on the Next button to proceed. 6. After the audio driver installation finishes, select the Finish button to complete the installation process. 76 |
Price & Availability of HS-26081
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |